Franklin FPS-2A 30 LPM 240V Three-Wire Bore Pump – Complete Pump, Motor & Starter Box

The Franklin Electric FPS-2A is a complete 4-inch submersible bore pump, motor and starter-box package designed for applications requiring dependable water flow across moderate to very high pumping heads.

Suitable for domestic water supply, stock watering, tank filling, irrigation, water transfer and general rural water systems, the FPS-2A range has a nominal duty flow of 30 litres per minute. Five motor and stage configurations are available to suit different pumping levels, elevations and pressure requirements.

Available Variants

Increasing the number of stages increases the available pumping head. The correct model must be selected using the required flow and total dynamic head—not bore depth alone.

What Is Included

• Franklin FPS 4400 Tri-Seal pump end

• Franklin 240V single-phase three-wire motor

• Franklin capacitor starter box matched to the selected motor

• Built-in removable spring-loaded check valve

• Four-inch waterproof cable splice kit

• Three-year Franklin Electric warranty, subject to the applicable warranty terms

A correctly matched external starter box is required for a three-wire motor and is included with every variant in this complete assembly.

The included starter box contains the motor-starting components. It should not be treated as complete dry-run, low-water-level, surge or system protection.

Key Features

• Complete pump, motor and starter-box assembly

• Nominal flow category: 30 litres per minute

• Nominal flow rating: 2 cubic metres per hour

• Motor sizes from 0.75kW to 3.7kW

• Twelve-stage to 59-stage configurations

• Designed for suitable 4-inch or larger bore casing

• Maximum pump diameter with cable guard: approximately 99.1mm

• 32mm / 1¼-inch BSPP female discharge

• Tri-Seal floating-stage hydraulic design

• Abrasion-resistant impellers and diffusers

• Corrosion-resistant Franklin Electric submersible motor

• Ceramic shaft sleeve and rubber discharge bearing

• Removable spring-loaded check valve

• Maximum water temperature: 49°C

• 240V single-phase, 50Hz operation

Optional Add-Ons

• Submersible electrical cable in the required length and thickness

• Pumptec or Pumptec Plus motor protection selected to suit the motor

• Bore head or bore cap

• Stainless-steel safety cable and cable grips

• Water-level probes and matching protection relay

• Kelco float switch

• Pressure tank and pressure-control equipment

• Plasson pipe fittings and connection components

Electrical cable must be sized according to the selected motor, total cable distance, voltage drop, starting current and installation conditions.

The motor, included starter box and any protection equipment must be connected and commissioned by a licensed electrician in accordance with the supplied wiring information, manufacturer instructions and applicable regulations.

The 2.2kW and 3.7kW variants place a substantial starting load on a single-phase electrical supply. Available supply capacity and cable sizing must be confirmed by a licensed electrician before purchase.

Selecting the Correct Model

Total dynamic head must account for the pumping water level, bore drawdown, vertical elevation, required outlet pressure and friction loss through the pipework, valves and fittings.

The 30 LPM rating identifies the pump family and is not a guaranteed output under every installation condition. Actual performance will depend on the selected model and operating head.

Contact The Pump Shed Australia with your bore depth, pumping water level, elevation, pipe size, pipe length, required flow and required pressure if you need assistance selecting the appropriate model.

FPS-2A - 30 LPM Range

How to read the FPS-2A table: Flow is shown across the top in litres per minute (LPM). Each number in the table is the approximate total head in metres that the listed FPS-2A model can produce at that flow. Only points inside the blue 24-41 LPM best-efficiency/warranty zone are shown; operation outside this zone is not covered by warranty.

FPS-2A - 30 LPM Range

How to read the FPS-2A three-wire table: Flow is shown across the top in litres per minute (LPM). Each number in the table is the approximate total head in metres that the listed FPS-2A three-wire model can produce at that flow. Only points inside the blue 24-41 LPM best-efficiency/warranty zone are shown; operation outside this zone is not covered by warranty.